Since the FC mounting hole is only 20mm × 20mm, 16mm × 16mm mounting is necessary.

FCの取り付け穴が20mm×20mmしか空いてないので16mm×16mm取り付け加工が必要ですね。

Since the FC mounting hole is only 20mm × 20mm, 16mm × 16mm mounting is necessary.

Cheap!(^-^) There are plenty of accessories for the cheap Especially the TPU parts come with you to a point where you lose your motivation to produce It may be useful for those who use Toothpick or tynywhoop batteries I don't do toothpick and I don't want to use the battery of tynywhoop Besides, I don't like Sharkfin The camera hits the 16x16 tower I used a camera mount from another company as a countermeasure Results All TPU parts go to the trash can (laughs) The frame itself is not cut, not even chamfered, let alone cross-sectional treatment We only have holes for 20x20 stacks, and when we use 16x16 stacks, we only need to work The motor hole is not a 2mm hole. When using a 2mm screw, this is also necessary. But processing is simple, and if you've worked with Japanese carbon, it might be a little unmotivated Don't worry about this frame Very easy to process (^-^) It's just a moment to drill a new hole or widen the hole It is a highly recommended frame for those who like processing (^-^)

安い！(^-^) 安い割には付属品が豊富です 特にTPUパーツは 制作意欲を失くすくらい付いてきます Toothpickやtynywhoopのバッテリーを使う方には便利かもしれません 私はtoothpickはやらないし tynywhoopのバッテリーを使う気もありません 加えてシャークフィンが好きではなく 16x16のタワーで組んでるのにカメラが当ります 対策として他社のカメラマウントを使ったため 結果TPUパーツは全てゴミ箱行きです(笑) フレーム自体は切りっぱなしで 断面処理どころか面取りすらされていません 20x20スタック用の穴しかなく 16x16スタックを使う際は加工するしかありません モーターの穴は2mm穴では無く 2mmのビスを使う際はこちらも加工が必要になります。 ただ加工は簡単で 日本製のカーボンを加工したことある方は 少々やる気が失せるかもしれませんが こちらのフレームは安心して下さい めっちゃ簡単に加工できます(^-^) 新しく穴を開けるのも 穴を広げるのも一瞬で完了 加工が好きな方には なかなかオススメのフレームです(^-^)

Cheap!(^-^) There are plenty of accessories for the cheap Especially the TPU parts come with you to a point where you lose your motivation to produce It may be useful for those who use Toothpick or tynywhoop batteries I don't do toothpick and I don't want to use the battery of tynywhoop Besides, I don't like Sharkfin The camera hits the 16x16 tower I used a camera mount from another company as a countermeasure Results All TPU parts go to the trash can (laughs) The frame itself is not cut, not even chamfered, let alone cross-sectional treatment We only have holes for 20x20 stacks, and when we use 16x16 stacks, we only need to work The motor hole is not a 2mm hole. When using a 2mm screw, this is also necessary. But processing is simple, and if you've worked with Japanese carbon, it might be a little unmotivated Don't worry about this frame Very easy to process (^-^) It's just a moment to drill a new hole or widen the hole It is a highly recommended frame for those who like processing (^-^)